Why is My Dishwasher Leaking?

Getting up in the morning to find a large puddle coming from the dishwasher is never a great to start the day.

Fortunately, most commonplace sources of dishwasher faults are comparably straightforward to determine and mend by yourself. Meaning you may not need to wash the dishes by hand that much, call an engineer or need to pay a high call-out fee.

So, if you’re feeling up to it find the operating manual if you know where it is, clean up the mess and so get something clean up any additional leaks and find out whether you can diagnose the fault. If you cannot call us for local dishwasher repair.

Simple Explanations of Dishwasher Faults as well as How to Fix Them

Many of the most commonplace causes of dishwasher faults aren’t actually due to a broken dishwasher . Before you start preparing yourself for an engineering task and watching numerous youtube tutorials there are a number of issues you might want to rule out first.

  1. Investigate to see if your dishwasher is aligned. If the dishwasher is not level water will easily pool and so spill out even if the dishwasher is working perfectly.
  2. Check you have been using the proper soap. You might be aware of this problem with your washer. An excess of detergent or using the incorrect type may lead an excess of bubbles, the bubbles bubble over resulting in a leak.
  3. Investigate your dishwasher door fully closes. If there’s a gap there may be a blockage, or you might have to fix the hinge or the locking mechanism.
  4. Check the filter located in the bottom of the tub for any easy to see drainage issues because if your dishwasher isn’t draining effectively this can cause it to overfill and so leak.

If none of the above issues apply it’s time to roll up your sleeves and really start a thorough check.

To make your life easier start with the door as well as test for any visible problems inside of the machine prior to moving on to the underneath. If you can identify as well as fix the issue without pulling out the dishwasher you’ll save yourself a lot of hassle.

Also make sure you disconnect the appliance first by either unplugging it or turning off the circuit breaker for the dishwasher.

Door Gasket

The door is no doubt the most everyday area for leakage as well as one of the quickest issues to resolve.

If the leakage is periodic the fault might be as simple as a large plate or another object pushing against the door thus preventing the door from sealing correctly.

On the other hand the door seal could have been dislodged or become split.

Examine the door seal and also investigate for any brittleness, mineral deposits or other debris, or any areas in which the gasket might have separated from the door.

Removing the seal and giving it a good scrub can help in some cases or you could be required to acquire a new gasket and replace it.

Water Inlet Valve (Solenoid Fill Valve)

The water inlet valve can also be a commonly seen issue. The inlet is in most cases found under the machine which means you will most likely need to remove the kick plate and could have to take off the door cover.

The fill valve opens and closes to allow water into the tub at various times during the programme. The fill valve may be showing a leak, shown with a slight drip, or it could be damaged thus not opening or closing properly during the programme.

In the case that the water inlet valve doesn’t close correctly this can mean that the dishwasher overfills, causing a leak.

Usually fill valve can’t be fixed, which means the entire component would need to be changed.

Leaking Hoses

Your dishwasher uses hoses to supply, empty and also recirculate water within the programme.

Two problems might develop when it comes to hoses.

  1. The seals can break or the connections might work loose thus it’s a good idea to have a look at all the connection points .
  2. The other problem than can easily happen over time is that hoses may become damaged or cracked.

Luckily broken hoses are relatively simple to procure and change.

Pumps and Seals

You can visually test the rubber seals that are part of the water pumps or motor to determine whether there is a leakage as well as replace them if there is.

The Float Switch

Either the float or the float switch could be broken causing the dishwasher to overfill.

When operating as it should the float will lift up with the water level until the desired or maximum water level is reached. The end piece of the float will then operate the switch. A blockage or breakage could be causing your issues.

Testing the switch will require electrical equipment but it might be obviously broken in which case replacing it should stop the leak.

Alternative Parts that Might Result in Leakage

A cracked wash arm or support may puch water under the door resulting in leakage. This can also often affect how well your dishes are being cleaned.

Broken or damaged lines might likewise result in this issue as could a broken pump cover if your dishwasher has one.

The motor shaft gasket might have degraded resulting in a leak. This will generally show as a leak coming from the underside of the machine.

Top Tips to Sort Out Your Dishwasher

  1. Spend less by changing the gasket instead of the entire part. In many instances, you are able to buy the gasket without the rest of the part which saves time as well as money.
  2. Investigate the simple fixes before you get more complicated. You don’t need to pull the whole dishwasher out if it’s the detergent that’s causing the leak.
  3. Take pictures at each step. This could make your life easier when you come to put the thing back together, explain the part you need in a store, and also identify the issue to a repair person if needed.
  4. Stay safe. Water and electricity do not mix so turn off the power first.
  5. If in doubt call a professional.

What To Do Next If Your Trouble Shooting Fails to Identify or Fix the Leakage

If the root of the issue can’t be discovered the next step you may take is to pull the dishwasher away from the wall to get better access underneath it as well as fill it with water to find out if the leakage can be seen that way.

If you are still in the dark your machine might only show a leakage if during a cycle. In this instance, you should employ a appliance repair person to determine as well as resolve the fault as there are safety risks of running the dishwasher with electrical elements uncovered.

More Dishwasher Problems:

  • Dishwasher Being Loud
  • Dishwasher Not Turning On
  • Dishwasher Not Draining
  • Dishwasher Not Drying
CLICK-TO-CALL